Key takeaways
- The CC1 and CC1 Pro share hardware, tanks, battery and full coverage rate. The Pro's difference is camera-driven verification of results.
- Treat list prices as starting points, not quotes. Confirm docks, water and accessories in writing.
- Scrubbing adds a tooling swap at the start of a shift, so plan labor for it.
- Docking, water and drainage can outweigh the price gap between the two models.
- Step up to the Pro when inspection time is your real labor cost on a messy floor.
Which model fits your floor
The Pudu CC1 and CC1 Pro are nearly the same machine on paper. Future Machines states that hardware, tanks, battery, runtimes and full coverage cleaning rate are officially identical on both models. The difference sits in software: the CC1 Pro adds a rear AI camera that checks cleaning results, re cleans missed spots automatically and produces heatmap reports.
For most facility managers, that makes the CC1 the sensible starting point when a scheduled pass on a predictable floor does the job and a person can spot check the results. The Pro earns its premium when verifying work without a walk through is worth more than the price gap, or when spills and traffic dirty the floor unpredictably.
A word on price first. We could not confirm the July 31, 2026 distributor list showing $21,995 for the CC1 and $23,995 for the CC1 Pro in this research, so treat those figures as unverified. List prices are not quotes. Your real cost depends on docks, water, accessories and financing terms.
What the Pro adds on the floor
The CC1 Pro's rear AI camera checks the result of each pass and re cleans spots it judges missed. Its heatmap reports show where the floor needed a second look. Pudu's CC1 Pro page says the machine automatically adjusts cleaning mode and intensity, which matters on floors that change from zone to zone.
The operation guide lists Guided Cleaning, Ultra Spot Clean and Cleaning Effect Detection as Pro functions. Summon Cleaning works with the MT1 series, so it only matters if your site already runs that line.
The speed figure is where readers get misled. Moboticsusa lists the Pro at 1,500 to 3,000 square meters per hour, depending on mode and layout. Anton Robots says that range applies to AI spot cleaning, while the full area rate is 700 to 1,000. Plan labor on the full area rate and treat the higher number as spot work.
Cleaning modes and the setup they create
The CC1 page lists four modes, sweeping, scrubbing, vacuuming and mopping, with suction up to 17,000 Pa and operating noise under 70 dB(A). Sweeping mode has three methods: sweep, vacuum and mop as the hard floor default, silent dust mopping for hard floors, and carpet vacuuming for short pile carpet as an optional component.
Scrubbing is the mode that adds labor at the start of a shift. Pudu's operation guide says it requires removing the side brush, installing the squeegee and fitting the scrubbing roller brushes. A scheduled scrub that starts with the wrong tooling is a missed night, so put that swap on the closing checklist.
Scheduled tasks run only provided that positioning is normal and there is sufficient power and water, the operation guide says. Floor type detection switches between sweep and vacuum on hard floors and vacuum only on carpet, according to Moboticsusa.
Docks, water and setup needs
Automatic charging, water refill and drain require an optional docking station, according to Pudu's pages and the operation guide. Without one, staff handle charging and water changes by hand, and that labor never appears on a list price.
Sites without plumbing have another route. Pudu's Mobile Water Station adds a 30 L clean tank and 30 L dirty tank, as listed by Robotics Norden and Pudu's CC1 page. The docking station needs a water supply, a floor drain and power, and it can be anchored to the floor or set against a wall, per One Stop Cleaning Shop.
Pudu's launch release dated September 23, 2025 describes a self clean docking station with a 100 W ultrasonic module, 65 degree hot water, more than 95 percent roller brush debris removal, and a claimed 35x maintenance efficiency gain. Those are vendor reported figures. The release also describes a loop in which the CC1 Pro detects a stain, docks, self cleans and resumes. Ask for test results on your own floor before you count on that loop.
Slopes, thresholds and open spec items
The operation guide says cleaning is for flat ground only, with no cleaning on visible slopes greater than 3 degrees, and an 8 degree maximum climb in non cleaning mode. Robotics Norden, a reseller, lists an 8 mm threshold limit while cleaning, 20 mm when not cleaning, and a 20 mm gap while cleaning. Confirm those figures against Pudu's current documentation before you plan a route over a lip, ramp or floor drain.
Robotsinternational says several CC1 Pro items are not published: IP rating, brush pressure, obstacle climbing height, maximum slope, sensor list and included items. It says these are confirmed at quotation. Treat them as open questions to close before signing, not as zero.
Where the CC1 is enough
The CC1 suits a flat, predictable floor with one or two zones, a fixed closing routine, and staff who check the floor by eye at opening. If the floor changes little from night to night, the Pro's camera mostly verifies work your team was already inspecting.
A repetitive route that finishes on time is the whole job. The CC1 runs that job on the same tanks, battery and coverage rate as the Pro, so the extra sensing has to earn its place on your floor.
Where the step up pays for itself
The Pro makes the most sense where mess is unpredictable: food spills, wet entries, or traffic that dirties a few spots heavily. Automatic spot re cleaning and heatmaps shorten the morning walk through, and that inspection time is where the savings sit. Price the gap against those minutes, and against any night a missed spot went unnoticed.
The Pro also gives you a record. A heatmap shows where the floor was cleaned, which helps when an owner, a franchisor or an auditor asks for proof. The CC1 gives you a completion status, and the Pro gives you evidence of coverage.
How a lease changes the comparison
Service Robot Co. leases robots only, on a 3 year lease with one fixed payment quoted after a site assessment. We are OEM neutral. We choose the right robot across manufacturers, then finance, deploy, integrate, train and service each unit through a nationwide US engineer network. For this pair, the CC1 or the CC1 Pro is one option we would evaluate against your docks, water and floor.
The site assessment is where the open items above get answered, including slopes, thresholds, dock placement and water access. Ask any distributor, including us, for these points in writing:
- Which docking station is quoted, and whether water, drain and electrical work is excluded
- Whether scrubbing tooling, squeegee kit and water station are included or priced separately
- Published IP rating, obstacle climbing height and maximum slope for the exact model quoted
- Who services the dock and camera, and the response terms if a unit goes down overnight
Frequently asked questions
Want a robot working for you?
Tell us the job and the site. We will recommend the robot, quote the lease, and keep it serviced.